Roads follow both ridge lines and water channels to provide easier movement across the land. Graded earthen channels may be interlinked to broaden the catchment areas of high dams, conserve the height of water, and transfer rainfall runoff into the most efficient high dam sites. Keyline designs include irrigation dams equipped with through-the-wall lockpipe systems, gravity feed irrigation, stock water, and yard water. Yeomans described a system of amplified contour ripping to control rainfall runoff and enable fast flood irrigation of undulating land without the need for terracing it. Yeomans published the first book on Keyline design in 1954. Yeomans invented and developed Keyline design in his books The Keyline Plan, The Challenge of Landscape, Water For Every Farm, and The City Forest. Keyline design is a system of principles and techniques of developing rural and urban landscapes to optimize use of their water resources.Īustralian farmer and engineer P. The "keyline" is a specific topographic feature related to the natural flow of water on the tract. Keyline design is a landscaping technique of maximizing the beneficial use of the water resources of a tract of land. JSTOR ( February 2008) ( Learn how and when to remove this template message)Ī keyline irrigation channel in Orana, Australia.Unsourced material may be challenged and removed. Please help improve this article by adding citations to reliable sources. But please at first check out the things i said above.This article needs additional citations for verification. Does the Value in Mobiflight is chaning ? it should be 0 if UP and 16383 if DOWN.Īdditional Note: In PMDG there exist own Offsets for the GEAR Lights. Start a flight get in the air and run your gear UP-DOWN-UP-DOWN. Then make a test with a P3D standard Aircraft ( NO PMDG). Please run Mobiflight and get shure the config is ACTIVE. To check if its a real problem or just a wrong use of you. But some basics like Parking Brake or Gear status "can" be used by standard offsets, too.īut "Maby" the FSUIPC 5 Updating last months ( P3D make a big update to 64bit system and FSUIPC, too) produce a issue. "Normaly" the Gear Transit should work in your PMDG wih that standard Offset, too. Presets are NOT always a final working system. But it not get off if Gear is Down ( like it should do) To use this "preset" you must edit it and enter some other settings (compare). That means the LED will light if Gear is NOT Up. thats more a example and not a solution !įor example here it use the correct Offset but it have no compare. )ĪND NOTE: The PRESETS in Mobiflight ( where you choose the "NoseGear-moving") are just a relict of the past. Is the problem the aircraft or is the problem a beginnerissue you did. If you already understand the basics then you be able to build a system for your AddOns ! ( Without that experience you not know. To work with this advanced Aircrafts you need individual informations and you must have a bit experience.įor your first steps i recommend to work with a standard aircraft that was include in your P3D. That means most of functions can NOT controlled by offsets from standard list ( or by the presets in Mobiflight). AddOns like PMDG mostly NOT use the standard stuff. The basic technics are build for FSX (or P3d) standard aircrafts. you can learn a lot within the first days ! ![]() Mobiflight is a great tool and the people here are cool. I think I am on a massive learning curve. Two days ago, I didn't have any idea how to set a circuit up and now I've set one up that I can control from a P.C. My apologies for appearing so inexperienced, my knowledge is limited but growing extremely fast extremely quickly. I have used the same method for the landing light as I did with the parking brake but I guess I'm missing a few things. (Great introduction and excellent as a learning tool ) I only have the Main Instrument Panel built so far so the Parking Brake will be quite a few steps away yet. I went through the tutorial with the parking brake LED and it worked fine. I am assuming that all the entrys are correct although the Output Value and FSUIPC value both say zero when I hit run. I believe my hardware is set up correctly as the LEDs light up when I press test. I haven't attempted to look at the compare, I still know too little about how it all works. I picked the one labelled Landing Gear Nose (moving). I have used the offset from the drop down menu. And may I say this is an outstanding program. Finding people with the same interests as mine is always a pleasure.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |